Skip to content
What's New?

TAMultitrack User Guide

This guide covers The Audio Magazine - TAMultitrack, an eight-track browser recorder with microphone recording, imported backing tracks, EQ, shared stereo effects, and local project storage.

1. Start a session

  1. Open TAMultitrack in a current browser. Use a desktop or a tablet in landscape, and connect headphones.
  2. Give the project a name. Select Full screen for a focused recorder view; use Exit full screen or Escape to return.
  3. If you have an audio interface, connect it before selecting an Input device. Device names may remain hidden until microphone permission has been granted.
  4. Select Check input, allow microphone access, and watch the Input L/R meter. Adjust gain on your microphone or interface. Input checking does not send the microphone to the speakers. Select Stop input check when finished.

2. Import a guide or backing track

Select Import on a channel and choose an audio file from your device. WAV and MP3 are common choices; other formats depend on the browser decoder. Files must be smaller than 50 MB and fit within the available timeline and audio-memory budget. The imported take starts at the playhead position. Use Start before importing if you want it to begin at zero.

Each track holds one take. Replacing an occupied track asks first. A stereo import retains its left and right channels regardless of the track’s recording-input selection. That selector controls the next microphone recording.

3. Arm a channel and record

  1. Select Arm on the channel you want to record. Only one channel is armed at a time. Selecting its Armed button again disarms it.
  2. Choose Mono or Stereo on that channel. Mono is appropriate for a single microphone. Track 8 defaults to Stereo, but every track can use either setting. Distinct left and right recording requires a source that supplies two channels; a mono source cannot become a genuine stereo recording merely by selecting Stereo.
  3. Move the playhead to the point where the take should begin. Existing tracks play during recording; the occupied take on the armed channel is excluded while you replace it.
  4. Set Count-in to Off, 1 bar, or 2 bars. Count-in clicks sound before recording even if the ongoing metronome is off.
  5. Select Record, play your part, and select Stop. The microphone is released after the take is completed.

Keep this page visible. Recording stops if the tab is hidden, the screen is locked, or the audio context is interrupted. The tool records one selected browser input at a time; it is not an eight-input simultaneous recorder. Microphone monitoring is deliberately off to avoid feedback. Use your interface’s direct monitoring if you need to hear the live input.

4. Use the metronome and correct late overdubs

Set Tempo from 30 to 240 BPM and choose 2–7 beats per bar. Enable the metronome before playback or recording. The click is not included in stereo mix exports. Headphones prevent it from being picked up acoustically by the microphone.

If new overdubs consistently land late, increase Input offset in milliseconds. This moves new recordings earlier; it does not move existing takes or automatically calibrate your hardware. The setting ranges from 0 to 500 ms. For a new recording at time zero, any corrected portion before zero is trimmed.

5. Mix the tracks

Use volume, pan, mute, and solo on each channel. Mute takes precedence over Solo. Open EQ / FX to adjust the low shelf at 120 Hz, mid band at 1 kHz, and high shelf at 6 kHz. Each EQ band offers up to 12 dB of cut or boost.

Reverb and Echo controls on a channel are sends to shared effects. They do not create separate reverbs or delays for each track. The shared panel provides Room, Plate, and Hall reverb, with a 0.2–8 second decay and a return level. The stereo delay provides 50–1,500 ms delay time, 1–8 repeats, and a return level. Each delay repeat alternates the left and right channels. Both returns feed the main stereo bus and are included in WAV mixdowns.

6. Read the meters

Track meters show channel levels after EQ, pan, and volume. Reverb and delay meters show their stereo returns. The master meter shows the combined stereo mix before the listening-level control. The separate input meter shows the microphone before recording processing.

Readings are peak dBFS, with a held peak and a latched CLIP indication. Reset peaks clears held values and clip indicators. These are browser sample-peak displays, not calibrated loudness or true-peak meters. Leave headroom rather than aiming for 0 dBFS. Lower track or effects-return levels if the master clips. Listening level changes your monitoring volume, not the exported mix.

7. Undo a take change

Undo restores the previous take after importing, clearing, or recording over a track. It keeps one take-change undo, not a full editing history. Opening another project or starting a new project clears it. There is no trim, move, fade, loop-recording, or punch-in editor in this version.

8. Save and recover your work

Clearing browser data can remove locally saved projects and recovery copies. Private browsing, storage quotas, and device storage pressure can limit persistence. Download a project file at useful milestones and before closing an important session.

9. Export your work

Aligned separate-track exports are capped at 320 MB to avoid excessive browser memory use. If that limit is reached, download the project instead.

10. Longer sessions and tablets

The timeline expands in 30-second steps, up to a 30-minute ceiling. The audio-memory display shows a shared session budget. Recording stops earlier if the budget fills; a 30-minute timeline does not guarantee 30 minutes across eight tracks. Stereo audio consumes twice the sample memory of mono at the same rate. Imported compressed file size does not indicate its decoded audio-memory use.

Tablets and lower-memory devices receive a smaller audio budget. At 48 kHz, the smaller budget is roughly 22 mono track-minutes or 11 stereo track-minutes shared across the whole session; eight equal-length tracks divide that total eight ways. Desktop budgets are approximately twice that. Physical device capacity, browser limits, effects, and exports add further overhead.

The landscape layout has been checked at tablet dimensions. Recording and USB-interface operation have not been verified on a physical iPad or Android tablet. Keep the screen awake and the page visible, wear wired headphones where possible, and test a short recording before relying on a device for an important session.

Scroll to Top